SSC JE Exam - highway engineering cross sectional elements geometric design pavement types materials tests Online Test (MCQ Quiz)

1. What is the primary purpose of camber in a highway pavement?

A) To provide a smooth riding surface B) To facilitate drainage of surface water C) To increase the load-bearing capacity D) To reduce tire noise

2. Which of the following is NOT considered a cross-sectional element of a highway?

A) Carriageway B) Shoulder C) Median D) Gradient

3. What is the recommended minimum sight distance for a crest vertical curve on a national highway in India?

A) Stopping Sight Distance (SSD) B) Intermediate Sight Distance (ISD) C) Overtaking Sight Distance (OSD) D) Absolute Minimum Sight Distance (AMSD)

4. The horizontal curve design for highways is primarily governed by which factor?

A) Traffic volume B) Superelevation C) Gradient D) Camber

5. Which type of pavement consists of a granular base and sub-base layers topped with a bituminous surface?

A) Rigid Pavement B) Flexible Pavement C) Composite Pavement D) Semi-Rigid Pavement

6. What is the main function of a median in highway design?

A) To provide parking space B) To separate opposing traffic streams C) To facilitate pedestrian crossing D) To increase the pavement width

7. The minimum radius of a horizontal curve is determined by the maximum allowable value of which parameter?

A) Gradient B) Superelevation C) Sight distance D) Camber

8. Which test is performed to determine the hardness of aggregates used in highway construction?

A) Crushing Strength Test B) Impact Test C) Abrasion Test D) Hardness Test (Mohs scale is not standard for aggregates)

9. What is the purpose of the 'Subgrade' in a pavement structure?

A) To provide a wearing surface B) To distribute wheel loads to the underlying soil C) To prevent surface erosion D) To improve the aesthetic appearance

10. The maximum design speed for a national highway in plain terrain, as per IRC standards, is typically:

A) 60 km/h B) 80 km/h C) 100 km/h D) 120 km/h

11. Which test is used to measure the resistance of aggregates to breaking down under gradual impact?

A) Los Angeles Abrasion Test B) Aggregate Impact Value Test C) Aggregate Crushing Value Test D) Water Absorption Test

12. What is the minimum width of a single lane carriageway on an NH in plain terrain?

A) 3.0 m B) 3.5 m C) 3.75 m D) 4.0 m

13. For a summit vertical curve, the sight distance required is generally:

A) Equal to Stopping Sight Distance (SSD) B) Equal to Overtaking Sight Distance (OSD) C) Less than SSD D) More than OSD

14. Which component of a flexible pavement directly receives the wheel load from the tires?

A) Sub-base B) Base C) Surface Course D) Subgrade

15. The rate of superelevation is limited by:

A) Maximum friction coefficient between tire and pavement B) Maximum allowable centrifugal force C) Minimum radius of curve D) All of the above

16. The 'Stripping Value' test for bitumen is conducted to assess:

A) Its viscosity at high temperatures B) Its resistance to stripping by water C) Its penetration value D) Its softening point

17. What is the primary function of shoulders on a highway?

A) To provide a buffer space B) To accommodate stopped vehicles and provide lateral support to the pavement C) To increase the number of lanes D) To improve drainage

18. Which type of vertical curve is used to connect two descending grades?

A) Crest Vertical Curve B) Sag Vertical Curve C) Summit Vertical Curve D) Valley Curve

19. The 'Aggregate Crushing Value' test determines the:

A) Resistance of aggregate to impact B) Resistance of aggregate to crushing under gradually applied load C) Resistance of aggregate to abrasion D) Hardness of aggregate

20. What is the minimum stopping sight distance (SSD) dependent on?

A) Design speed and reaction time B) Gradient and superelevation C) Radius of horizontal curve D) Width of carriageway

21. Which material is typically used as the surface course in a flexible pavement?

A) Cement Concrete B) Bituminous Concrete C) Gravel D) Crushed Rock

22. The minimum length of a horizontal curve is determined by:

A) Stopping Sight Distance (SSD) B) Overtaking Sight Distance (OSD) C) Superelevation requirements and mechanical widening D) Traffic volume

23. What does the 'Penetration Value' of bitumen indicate?

A) Its viscosity at a specific temperature B) Its consistency or hardness C) Its resistance to weathering D) Its flash point

24. The purpose of providing a 'Gutter' along the edge of a highway is to:

A) Support the pavement edge B) Collect and channel surface water away from the pavement C) Provide a space for pedestrians D) Reduce noise pollution

25. For a sag vertical curve, the sight distance required is generally:

A) Equal to Stopping Sight Distance (SSD) B) Equal to Overtaking Sight Distance (OSD) C) Less than SSD D) More than OSD

26. Which test is used to determine the resistance of aggregates to disintegration by the action of weather?

A) Soundness Test B) Flakiness and Elongation Test C) Specific Gravity Test D) Water Absorption Test

27. The 'Gradient' on a highway refers to:

A) The width of the carriageway B) The rate of rise or fall of the road surface C) The curvature of the road D) The drainage slope

28. In a rigid pavement, the primary structural component is the:

A) Bituminous layer B) Granular sub-base C) Cement Concrete slab D) Compacted subgrade

29. Which of the following is a factor influencing the design of a vertical curve?

A) Rate of change of deflection angle B) Rate of change of grade C) Traffic density D) Skid resistance

30. The 'Softening Point' test for bitumen is used to determine:

A) Its viscosity at road temperatures B) The temperature at which it softens and begins to flow C) Its resistance to aging D) Its flash point

31. What is the main advantage of flexible pavements over rigid pavements?

A) Higher load-carrying capacity B) Lower initial cost and adaptability to stages of development C) Greater durability under heavy loads D) Less susceptible to temperature variations

32. The 'Rate of Change of Superelevation' is important for:

A) Ensuring structural stability of the pavement B) Preventing discomfort to passengers and ensuring smooth transition C) Increasing the friction coefficient D) Reducing the required sight distance

33. The 'California Bearing Ratio (CBR)' test is primarily used to assess the strength of:

A) Bitumen binder B) Aggregates C) Subgrade soil D) Surface course material

34. What is 'Mechanical Widening' of a horizontal curve?

A) Increasing the pavement width due to superelevation B) Increasing the pavement width due to the slow-moving vehicle's larger turning radius C) Increasing the pavement width to accommodate shoulders D) Increasing the pavement width for aesthetic reasons

35. Which type of pavement is characterized by a concrete slab acting as a continuous bridge over the subgrade?

A) Flexible Pavement B) Rigid Pavement C) Composite Pavement D) Semi-Rigid Pavement

36. The 'Impact Value' test on aggregates measures their:

A) Resistance to crushing B) Resistance to sudden shock or blow C) Resistance to abrasion D) Resistance to weathering

37. What is the purpose of a 'Median Opening' on a divided highway?

A) To allow emergency vehicle access B) To facilitate U-turns and other turning movements C) To provide a safe crossing for pedestrians D) To improve drainage

38. The 'Flakiness Index' of aggregates indicates:

A) Their resistance to crushing B) The proportion of flaky particles in the sample C) Their resistance to abrasion D) Their shape characteristics

39. Which geometric design element is crucial for ensuring safe and comfortable negotiation of curves?

A) Gradient B) Sight Distance C) Superelevation D) Camber

40. What is 'Retained Strength' in the context of bitumen-aggregate mixtures?

A) The strength of the mixture after aging B) The strength of the mixture after exposure to water, expressed as a percentage of its original strength C) The load-bearing capacity of the mixture D) The resistance to deformation

41. The minimum stopping sight distance (SSD) is influenced by the coefficient of friction between the tires and the pavement surface and the:

A) Gradient of the road B) Reaction time of the driver C) Width of the carriageway D) Radius of the horizontal curve

42. What is the primary function of the 'Binder Course' in a flexible pavement?

A) To distribute wheel loads to the base course B) To provide a smooth wearing surface C) To bind the surface course and the base course together D) To prevent water infiltration

43. The 'Rate of Change of Grade' is a critical parameter for the design of:

A) Horizontal Curves B) Vertical Curves C) Shoulders D) Medians

44. Which test is used to determine the resistance of bitumen to flow at elevated temperatures?

A) Penetration Test B) Ductility Test C) Softening Point Test D) Viscosity Test

45. What is the purpose of 'Sight Distance' in highway design?

A) To allow vehicles to turn B) To provide a clear view of the road ahead for safe driving C) To determine the pavement thickness D) To calculate the superelevation

46. Which of the following is a characteristic of a 'Composite Pavement'?

A) Only bituminous layers B) Only cement concrete layers C) A combination of cement concrete and bituminous layers D) Only granular layers

47. The 'Los Angeles Abrasion Test' is used to evaluate the:

A) Hardness of aggregates B) Toughness of aggregates C) Resistance of aggregates to wear D) Soundness of aggregates

48. What is the primary function of a 'Kerb' or 'Curb' on a highway?

A) To provide a smooth riding surface B) To demarcate the edge of the carriageway and protect the pavement edge C) To increase the pavement width D) To facilitate drainage

49. The 'Ductility Test' for bitumen measures its ability to:

A) Resist flow at high temperatures B) Stretch without breaking C) Resist abrasion D) Absorb water

50. Which parameter is NOT directly considered in the calculation of Stopping Sight Distance (SSD)?

A) Design Speed B) Total Reaction Time C) Coefficient of Longitudinal Friction D) Gradient of the road (for uphill, it reduces SSD, for downhill it increases SSD, but the basic formula uses it)

highway engineering cross sectional elements geometric design pavement types materials tests - Online Test

Test Results